Pages

NEWS

The articles of the site

 


The laying

 

Pose of the product RESIMARMO by three workers of RESIMARMO Italia

Pose of the product RESIMARMO by three workers of RESIMARMO Italia.

 

Prices applied products

The RESIMARMO® product is composed of two main products,

  • first of all aggregates (or granulates) of marbles 

       then 

  • the RESIFIX marble resin.

They are mixed during laying. They have been carefully selected in order to provide complete security for interior and exterior floors.

RESIFIX is a single component product. It is a liquid elastomeric polyurethane binder, aliphatic, moisture curing and solvent, and finally it is cold-processable. The compound « well dosed » with a natural mineral grain, produces a paste that allows the realization of coatings for floors. The final surface is a compound without fittings, flexible and resistant to cracking. The different tones of the aggregates make it possible to obtain multiple chromatic effects.

RESIMPER is also a single-component, ready-to-use product also applied cold. It is presented in liquid form, in contrast to the hardened state it creates as a continuous pavement membrane. Without joints and overlaps it does not fear moisture.

RESIPRIMER is a bi-adhesive epoxy component in an aqueous dispersion. It is used as a floor preparation for the RESIMARMO® line, also based on polyurethane resin.

RESIPROTEC is a stable and transparent product. It has a high shock performance, similar to a moisture curing component. In addition, the quality of the aliphatic polyurethane resin provides high UV resistance. It is a product for solid and flexible coatings with high resistance to abrasion and wear. In addition it is not sensitive to chemicals, dilute solutions of acids and bases. Finally chlorinated water, salt, fuels and lubricants of all kinds do not disrupt it.

RESITEX

RESITEX is a TNT (thermally bonded geotextile fabric), based on polyester / polyamide synthetic fibers, with high elasticity and high tensile strength.

RESITEX 80

RESITEX has been developed to be applied in situ by the interposition of fresh over and between the different layers of RESIMPER resin, in order to obtain a thickness as homogeneous as possible and consequently an optimal distribution of the product in limiting the effect of leaks.

RESITEX 200

It is recommended for the ultimate abrasion protection and a homogeneous distribution of the unladen weight of the support coated with RESIMPER membranes of highly elastic polyurethane. Ideal in situations that require additional armor protection, or protection and optimum thickness distribution, with minimal loss of mechanical properties.

Product compatible with solvents and strong absorption. Flexible and adaptable to uneven surfaces, edges and corners, critical points of lifting and overlaps of old bituminous membranes, Ideal to assemble junction points between interdependent media or a different type or different material, cracks and macro- cracks, joints and cuts, etc …
High elasticity, in order to maintain as much as possible the mechanical properties of the membranes, which increases its resistance to perforation and perforation due to plant roots.
Inner and outer edges, front reinforcement, backbones and other singular points or as a « weed control » system prior to installation of the RESIMARMO® system.

RESITEX 200 membrane protection RESIMPER for layering of: concrete tiles, wood, wood panels, composite materials, cement boards, floating floors, etc …

 

Technical certifications obtained

  • ETA : European Technical Assessment document Nº 06/0263 – CE marking : 10 and 25 years.
  • Flat roof external fire exposure Nº 06/32301345
  • Roof 45º fire resistance Nº 08/32309237
  • Root perforation no RESIMPER Nº 07/32305556 with RESIMPER Nº 07/32305557
  • Abrasion Taber Nº 10/101.729-1626
  • QUALICONSULT : Notebook of Technical Terms CCT nº 50 712 004 096 MS
  • BBA : British Board of Agreement 11/4836
  • IETcc report 19.221-II (2007) on thermal resistance.

 

RESIMARMO Technical Certifications

 

URGENT APPEAL: We need distributors to cover different sectors available in United States. If you are interested, join us. Fill out the form below and become our exclusive partner in your state.

TO BECOME PARTNER

Complete this form to become a RESIMARMO Distributor.
  • For maximum security on our sites, you are invited to solve this puzzle. Write your answer below the CAPTCHA field.
  • Ce champ n’est utilisé qu’à des fins de validation et devrait rester inchangé.

 

 The product RESIMARMO - Logo of colors

The resins

The marble resin - Resin pot RESIFIX

Resin pot RESIFIX.

 

Resine Prices

Marble resin

A marble resin is a polymeric product (natural, artificial or synthetic) that is a basic material for the manufacture of plastics, textiles, paints (liquid or powder), adhesives, varnishes, polymer foams, etc. It can be thermoplastic or thermosetting.

A solid or semi-fluid, vitreous, flammable, water-insoluble, yellow or brown-coloured organic substance, spontaneous or induced exudation of certain plants, particularly conifers and terebinthaceous plants (this substance extracted from pine and fir).

 

Pine resin

Pine resin.

We don’t say « plastics »anymore, we say « resin. »

In a reinforced plastic material, marble resin, also known as a matrix, is a very fluid or highly viscous matrix, used as a binder to make contact between the various reinforcing particles, such as fibres, balls or microspheres (small spherical geometry particle with a diameter of the order of one micrometer[between 1 µm and 1 mm]. The micro-spheres are sometimes called « micro-particles » or « microbead » of glass.
For example, SMC (Sheet Moulding Compound) prepregs include polyester resin, reinforcement (matt, fabric or fibre), fillers and a pre-mixed catalyst (hardener). This ready-moulded mixture for hot compression molding is in sheet form.

Since the term « plastic » has a pejorative connotation for some consumers, the word « resin » is often used by manufacturers in place of « plastic » and marble resin follows the same logic.

The SPI coding system for the identification of resins is a code developed in 1988 by the Society of the Plastics Industry to facilitate the sorting and recycling of plastic bottles and containers.

It is adopted in Germany as DIN 6120, then in Europe, and is applied voluntarily by manufacturers, but must nevertheless comply with a precise codification in accordance with a European Commission decision of 28 January 1997 (97/129/EC).

Technical certifications obtained

  • ETA : European Technical Assessment document Nº 06/0263 – CE marking : 10 and 25 years.
  • Flat roof external fire exposure Nº 06/32301345
  • Roof 45º fire resistance Nº 08/32309237
  • Root perforation no RESIMPER Nº 07/32305556 with RESIMPER Nº 07/32305557
  • Abrasion Taber Nº 10/101.729-1626
  • QUALICONSULT : Notebook of Technical Terms CCT nº 50 712 004 096 MS
  • BBA : British Board of Agreement 11/4836
  • IETcc report 19.221-II (2007) on thermal resistance.

 

The marble resin - RESIMARMO Technical Certifications

 

 

 

 

The marble resin - Logo of color

 

 

Simple products

 

The marble aggregates - Prices in the world

Prices in the world.

 

RESIMARMO® Product Prices

The marble aggregates - Price marble aggregatesThe marble aggregates, a noble product and design

The marble aggregates - Resine Prices

The marble aggregates form a top-of-the-range covering composed of 100% marble gravel. Non-slip, draining or waterproof. It can be installed both indoors and outdoors.

 

 

 

The marble aggregates - Marble aggregates and profiles

Marble aggregates and profiles.

 

For a long time now carpeting has no longer been applied to the floor, PVC floors and floors have gone out of fashion as well, and the coolness of the tiles has discouraged more than one.
The marble aggregates are a good alternative: it is a noble, unique, innovative and beautiful product.

 

The marble aggregates - Pool of a Nice customer in France

Pool of a Nice customer in France.

 

The marble aggregates: This year, I’m building my house! But so much work!  First the terrace! The swimming pool is very beautiful but it will have to be highlighted because the floor is completely out of use…

Today, when you settle down, either, you choose a « turnkey » property: you put your luggage down and you are quiet, no work!
Either one invests in a property that is less expensive but in which there will be more work to be done. In this case, the possibilities of having a house or apartment that looks like us will be more important.
In our time, more and more French people are placing great importance on feeling at home and making their homes a place that looks like them:

  • wall colour,
  • choice of furniture,
  • layout…

But also the floor covering.

  • Carpet,
  • floor,
  • PVC,
  • Tiles…

A large panel !
What to choose when you want a design floor that is out of the ordinary ?
Unlike tiles, marble aggregates form a non-slip, draining surface for added safety. No more puddles on the terrace and no more children’s falls or unexpected slips. It is in perfect safety that one can evolve on a marble granulate floor.
Its little plus is that it doesn’t fade over time.

So, the sun can heat up as long as it wants, your floor will always remain marble !

 

 

 

 

 

The marble aggregates - Logo of color

 

The marble aggregates

 

The marble aggregates - Color Verde alpi

Color Verde alpi.

 

The marble aggregates - Table tonnage area thicknessThe marble aggregates - Prices marble aggregate.The marble aggregates are naturally eroded to remove sharp edges and make the soft contact under the feet.
The decorative marble aggregates of the RESIMARMO® range are extraordinarily resistant to mechanical stresses. The reflections of each of the shades will allow you to create unique surfaces both in pedestrian and pedestrian way.
All these products available in washed and dried (PREMIUM), are compatible for the realization of drainage floors in aggregates plus resin.
These mineral aggregates are very luminous because marble is a material that reflects a lot of light. Your mineral space will therefore be considerably cleared with this type of aggregate.
These products, once washed and dried in suitable large drums which can contain several tons, are compatible for producing asphalt mixes.
These decorative aggregates semi rolled in large mechanical drums are products of our own manufacture, therefore 100% Italian ! Their rounded shape gives them a very pleasant softness under the feet.
These aggregates are mostly made of marble, and are the most requested by all of our customers. You have below a wide choice of colors for the realization of your outer mineral space, inside the house as in the garden. The richness and nuances of colors will allow you to create an original space, the only limits will be « your imagination ».

The whole of our collection consists of Marble and of quartz. The Quartz aggregates are mainly used to make figures embedded in the marble aggregates. Practically everything you want is possible, from logos to drawings, animal images or anything else you would like to see under your feet in the thickness of your floor-covering made of marble. The latter can be used for the mineral decoration of your gardens, patios, terraces, or even inside your home to give a touch of light color out of the ordinary. These are unique and rare pieces coming directly from Brazil. The latter can be used for the mineral decoration of your gardens, patios, terraces, or even inside your home to give a touch of light color out of the ordinary.
Contact us so that we can study together your project and advise you at best.

 

The marble aggregates - Phone-number

 

 

Please contact us by e-mail:

commercial.service@resimarmo.com

 

technical.service@resimarmo.com

 

 

 

The marble aggregates - Logo of color

 

 

RESIPROTEC

 

Coating terrace pool (Luberon in France)

Coating terrace pool (Luberon in France).

 

RESIPROTEC

 

RESIPROTEC is steady, transparent, he has high mechanical performances similar to a compound hardening to the humidity. The resin of polyuréthane aliphatique allows an excellent resistance the UV. It is a product of strong, supple coatings, that resists the abrasion well and to wear. He/it doesn’t fear the chemicals, the solutions diluted of acids and bases, of chlorinated water, of salt, fuel and lubricants of all sorts. He/it creates an excellent protection of surface of soils submitted to an intense wear. RESIPROTEC doesn’t whiten under the inclemencies, he doesn’t change a very color when he is exposed to the UV rays, he is therefore perfectly advisable for the outside applications. For the application he/it is recommended to have a good environment of ventilation.

 

RESIPROTEC-1RESIPROTEC-2RESIPROTEC-3

APPLICATION

Can be applied by roller, brush or airless. Although not mandatory, it is recommended to use the full contents of each pot. If this is not the case, make sure it is completely watertight after use (risk of solidification). It is possible to adjust the viscosity with RESIGLIDE. Never dilute with solvents reactive with polyurethane (eg universal solvent or with alcohols).

Uses

  • Aires of parking to intense traffic, garages, parking of cars.
  • Excellent for the waterproofing.
  • Restoration of old domes of fiberglass, flat roofs, polycarbonate, other composite materials, etc.
  • Floors of concrete and polymeric.
  • Tightness and protection of the metallic structures, floor-coverings printed matter, micro cements, leveling maltine, mosaics, mineral gravel.
  • Produced of supple slip to quartz, the corindon, of rubber, of the dust, etc.

Advantages

  • A product to unique component, easy to use.
  • No possible mistakes therefore not of lost time.
  • Stability of the colors in the time under the UV.
  • Excellent resistance to the abrasion and to wear.
  • Fast hardening and protection of the paintings.
  • Good capacity of etandage.

Available colors

Transparent (the version no brilliant is available while using the » Matting Additive » (to see technical card above).

Technical certifications obtained

  • ETA : European Technical Assessment document Nº 06/0263 – CE marking : 10 and 25 years.
  • Flat roof external fire exposure Nº 06/32301345
  • Roof 45º fire resistance Nº 08/32309237
  • Root perforation no RESIMPER Nº 07/32305556 with RESIMPER Nº 07/32305557
  • Abrasion Taber Nº 10/101.729-1626
  • QUALICONSULT : Notebook of Technical Terms CCT nº 50 712 004 096 MS
  • BBA : British Board of Agreement 11/4836
  • IETcc report 19.221-II (2007) on thermal resistance.

 

Technical certifications obtained

 

 

CONTACT FORM

Visitor contact form
  • For maximum security on our sites, you are invited to solve this puzzle. Write your answer below the CAPTCHA field.

 

 

 

 

Logo of color

 

 

RESIPRIMER

 

Development the beaches of the pool

Development the beaches of the pool.

 

RESIPRIMER

 

RESIPRIMER is a composed epoxy, promoter of cohesion in a sticky scattering. That is to say that one uses it to prepare soils for the components of RESIMARMO®. RESIPRIMER is ideal for all applications to the problems of light humidity, in surface or to repulse the very light ascents of humidity (max 4%). It is simple to put it.

Uses

  • The systems époxy and polyuréthane.
  • As a layer of adhesive between the new soils and the old.
  • To excel in case of light ascents of humidity.
  • Adhesion for the sheet metal, zinc and…
  • Protection for floors concrete.

Feature

  • Easy and simple (to basis of water) application.
  • To accelerate the catalysis to low temperatures (0 ° with a special additive).
  • No-flammable.
  • No odor.
  • Simple cleaning.
  • Good adhesion.
  • Good resistance to wear.

 

RESIPRIMER-1

RESIPRIMER-2

 

Support preparation

Concrete surfaces must be previously prepared by sandblasting or any other suitable means. Remove all dust and loose material before priming.

Environmental precautions

Empty containers must be handled with the same precautions as if they were full. Treat empty containers as hazardous waste, and transfer them to an authorized waste manager. If the contains still have some material left, do not mix with other product before considering the risk of potential dangerous reactions. Never mix in volumes larger than 5 litres in order to prevent a dangerous heat evolution.

The temperature of the support must be consisted between 15°C and 40° C. If the temperature is superior in 45º complementary measure CS must be adopted, following the manufacturer’s instructions. The conditions of low temperature and the elevated humidity are unfavorable to the hardening of the product.

Product certifications RESIMARMO

  • ETA : European Technical Assessment document Nº 06/0263 – CE marking : 10 and 25 years.
  • Flat roof external fire exposure Nº 06/32301345
  • Roof 45º fire resistance Nº 08/32309237
  • Root perforation no RESIMPER Nº 07/32305556 with RESIMPER Nº 07/32305557
  • Abrasion Taber Nº 10/101.729-1626
  • QUALICONSULT : Notebook of Technical Terms CCT nº 50 712 004 096 MS
  • BBA : British Board of Agreement 11/4836
  • IETcc report 19.221-II (2007) on thermal resistance.

 

RESIMARMO Technical Certifications

 

 

CONTACT FORM

Visitor contact form
  • For maximum security on our sites, you are invited to solve this puzzle. Write your answer below the CAPTCHA field.

 

 

 

 

 

Logo of color

RESIMPER

 

Beaches of pool in aggregates of marbre-(Geneva)

Beaches of pool in aggregates of marbre-(Geneva).

 

RESIMPER

 

RESIMPER

RESIMPER is ready to use and apply to cold weather. He is presented under liquid shape, but in the strong state he/it creates a membrane without joint and doesn’t fear the humidity. Elastic and « breathing », the surfaces follow the movements of the land. Non-skid, he/it is resistant to the abrasion and to the shocks, to the inclemencies as well as to the chemicals. RESIMPER adheres to the support of the underside very well, even to different geometries or difficult of access, RESIMPER doesn’t need dilution (RESIGLIDE authorized max. 10%).
Applied with a brush or with a roller, It permits an adherent hangs specific. It is recommended for the critical zones as corners, the sky lights, the sides, the overlaps.
Not to apply on humid surfaces (trap of points of dew).

Uses

Applicable on: old bituminous girdles or slates bituminous, former acrylic coatings, slates, concretes, mortars, bricks, sandstone made of fibro-cement, shingles of wood, ceramic, oxidized asphalt, wood, steels, zincs, aluminiums, fiberglass, composite materials, etc.

Main applications

  • Terraces, balconies, isolated roofs, roofings, or metallic panel, etc.
  • Kitchens, bathroom, (showers) and places difficult of access by the inside.
  • Parking lots, local techniques, flat roofs or in slope.
  • Stairs, tribunes, steps.
  • Channels and deposits of water.

 

RESIMPER-1

RESIMPER-2

RESIMPER-3

 

 

Ceaning and maintenance

A maintenance work must be carried out regularly on the treated roofs according to the intended use.

This work includes the following tasks :

  • Leaf removal
  • Grass, dirt, moss and other vegetation removal
  • Keeping storm water system in good working order.
  • Ensure gratings are in place, in order to prevent gutter obstructions.
  • Check proper condition of several structures (flashing, seams, retaining walls…)
  • Verification of possible damages due to improper use.

If an esthetic appearance of the roof is an important issue, it is essential to regularly clean the surface with water (some mild detergent may be added), according to the use.

It may be necessary to reapply decorative layers (RESIMPER, RESIPROTEC) if they are worn out due to traffic, weather, corrosion, etc.

For stain removal, a surface treatment with RESIGLIDE or isopropyl alcohol may be attempted. Strong acids are totally inadequate. Some solvents may damage the membrane. If this happens, the affected area has to be cut and repaired with a new RESIMPER application.

Technical certifications obtained

  • ETA : European Technical Assessment document Nº 06/0263 – CE marking : 10 and 25 years.
  • Flat roof external fire exposure Nº 06/32301345
  • Roof 45º fire resistance Nº 08/32309237
  • Root perforation no RESIMPER Nº 07/32305556 with RESIMPER Nº 07/32305557
  • Abrasion Taber Nº 10/101.729-1626
  • QUALICONSULT : Notebook of Technical Terms CCT nº 50 712 004 096 MS
  • BBA : British Board of Agreement 11/4836
  • IETcc report 19.221-II (2007) on thermal resistance.

 

RESIMARMO Technical Certifications

 

 

CONTACT FORM

Visitor contact form
  • For maximum security on our sites, you are invited to solve this puzzle. Write your answer below the CAPTCHA field.

 

 

 

 

 

Logo of color

RESIFIX

 

RESIFIX - Beaches of pool with reasons

Beaches of pool with reasons.

 

RESIFIX

 

RESIFIX

The RESIFIX resin is a compound binder of polyuréthane, liquid elastomer, aliphatiques, even hardening to the humidity, solvent, calm to cold weather. The product « measured out » well with aggregates of marble, produces a flexible dough that permits to achieve coatings of soils as inside as outside. There is not an ungainly joint, the surface is flexible, non-skid and permits an excellent drainage. The different hues of marble used offer the possibility to get multiple effects of color, the geometric motives, the strips or the changes of coloration in a same surface.

 

Resin pot RESIFIX

Resin pot RESIFIX.

 

 

RESIFIX-1

RESIFIX-2

REQUIREMENTS OF SUPPORT

RESIFIX has a good cohesion and a good resistance to the compression, he lands on soils without dirty humidity or ascents of humidity.
The support must be clean and dry, it must be exempt of traces of oil, of grease, of wax, milt of cement, or of all something else that could compromise a good adhesion of the compound.
Of the temperature of the substratum must be consisted between 10ºC and 25ºC.
For the new tiles of concrete freshly streams, you should wait for at least 21 days before applying the product.

The surface to be treated must have the following minimum mechanical strength:

  • Minimum cohesion 1.5 MPa.
  • Compressive strength: greater than 25 MPa.

The substrate must be free from water or water vapor pressure (max. 4%).
The surface must be clean, dry and free of friable or little adhesion. It must also be free of oil, grease, wax, or any substance that can affect adhesion.
For more information on the treatment of singular points, contact our technical department.
The delimitation of the application space can be ensured by means of an aluminum profile previously fixed on the support.
The substrate temperature must be between 10ºC and 25ºC.
If there is a suspicion of moisture in the substrate, a suitable primer (RESIPRIMER) should be used.
on new concrete or mortar, wait at least 21 days before applying the RESIMARMO® system.

ATMOSPHERIC CONDITIONS

It is preferable that the ambient temperature is between +10 and + 30ºC. The relative humidity of the air between 30% and 80%

DOSAGE

The dosage of the mixture of RESIFIX with the aggregates is as follows:

AggregatsRESIFIX
Non-porous regular3 à 5 %
Irregular porous5 à 7 %
AggregatsRESIFIX

Technical certifications obtained

  • ETA : European Technical Assessment document Nº 06/0263 – CE marking : 10 and 25 years.
  • Flat roof external fire exposure Nº 06/32301345
  • Roof 45º fire resistance Nº 08/32309237
  • Root perforation no RESIMPER Nº 07/32305556 with RESIMPER Nº 07/32305557
  • Abrasion Taber Nº 10/101.729-1626
  • QUALICONSULT : Notebook of Technical Terms CCT nº 50 712 004 096 MS
  • BBA : British Board of Agreement 11/4836
  • IETcc report 19.221-II (2007) on thermal resistance.

 

RESIMARMO Technical Certifications

 

 

CONTACT FORM

Visitor contact form
  • For maximum security on our sites, you are invited to solve this puzzle. Write your answer below the CAPTCHA field.

 

 

 

 

Logo of color

Resins

 

Resin pot RESIFIX

Resin pot RESIFIX.

 

Resins

 

RESIFIX

RESIFIX resins, like many resins, is a single component binder of polyurethane, elastomer liquid, aliphatic, hardening with moisture, solvent, realizable with cold. The compound « well dosed » with natural marble aggregate, produces a paste that allows the realization of coatings for internal and external floors. There is no unsightly joint, the surface is soft, non-slip and allows excellent draining. The different marble tints used offer the possibility of obtaining multiple color effects, geometric patterns, strips or color changes in the same surface.

 

The resins - Resin pot RESIFIX

Resin pot RESIFIX.

SUPPORT REQUIREMENTS

The substrate must have the following mechanical properties:
-Chésion: Minimum 1.5 MPa.
-Resistance to compression: 25 MPa minimum.
The surface must be free of residual moisture or moisture rise.
The substrate must be clean, dry and free from loose and brittle parts, the moisture content must be less than 4%, no trace of oil, grease, wax, release agents and cement mildew, or Any other thing that could compromise good adhesion of the compound.
The temperature of the substrate must be between 10ºC and 25ºC.
If you suspect residual moisture on the substrate or moisture rise, you should use a specific pretreatment for moist surfaces.
For freshly poured concrete slabs or a new one, you will need to wait at least 21 days before applying the RESIMARMO® product.

RESIMPER

RESIMPER is a single-component, ready-to-use, cold-applied product. It is presented in liquid form, but in the hardened state it creates as a continuous roadway membrane, without seams and overlaps and does not fear moisture). Elastic and « breathable », the coated surfaces are able to follow the movements of the support. Non-slip, resistant to abrasion and impact, weather and chemicals and extreme temperatures, it adheres well to the underlying support, even at different geometries or difficult to access, does not usually need to Dilution (maximum permissible RESIGLIDE thinner 10%).
Applied with a roller, brush or airless, it allows a grip with specific grip. It is recommended for critical areas such as corners, edges, dormers, chimneys, overlaps and old « macrocavillature » bituminous sheaths, combined with polyurethane sealant.
WARNING MOISTURE MAX 4%! Do not apply to moist surfaces (dew point traps).

USES

Applicable to: old bituminous sheaths or bituminous slates, old acrylic coatings, slates, concretes, mortars, bricks, fibro-cement sandstones, wood shingles, ceramics, oxidized bitumen, wood, steels, zinc, aluminum, glass fibers Composites, etc …

PRINCIPAL APPLICATIONS

  • Balconies, terraces, roofs, insulated roofs or metallic panel, etc.
  • Bathroom (inside showers), kitchens and places hard to access from the inside.
  • Flat or sloping roofs, car parks, technical rooms.
  • Platforms, grandstands, stadiums, stadiums.
  • Water channels and deposits.

RESIPRIMER

RESIPRIMER is part of the resins, it is an epoxy component bi promoter of adhesion in an aqueous dispersion. It is used as a floor preparation for the RESIMARMO® line based on polyurethane resins. RESIPRIMER is the ideal primer for all applications with small problems of light moisture on the surface or to repel very slight moisture rise (max 4%). Moreover it is simple and safe to apply.

USES

  • Primer for epoxy and polyurethane resins systems.
  • As a layer of adhesive between new and old concrete floors (construction joints).
  • Primer in case of slight rise of humidity.
  • Adhesion primer for sheet, zinc and alloys.
  • Protective finish for concrete floors.

CHARACTERISTICS AND BENEFITS

  • Easy and safe application (water-based).
  • Ability to accelerate catalysis at temperatures close to 0 ° with a special additive.
  • Non-flammable.
  • Little odor.
  • Easy cleaning.
  • Excellent adhesion.
  • Good resistance to abrasion.

RESIPROTEC

RESIPROTEC is stable transparent, it has a high performance similar to a moisture curing component. The quality of aliphatic polyurethane resins provides high UV resistance. They are solid and flexible coatings with high resistance to abrasion and wear, chemicals, dilute solutions of acids and bases, chlorinated water, salt, fuel and lubricants. all kinds. Creates excellent surface protection for floors subject to intense wear. These resins products do not undergo whitening due to the weather, they do not change color when exposed to UV rays, so they are recommended for outdoor applications. They are available for all pigmented colors but will only land on site, at the time of use. For the application it is recommended to have a good ventilation environment.pigmented RAL colors but only on site, at the time of use. For the application it is recommended to have a good ventilation environment.

USES

  • Garage and parking areas with heavy traffic, car parking lot.
  • Excellent for waterproofing with polyurethane polyurea.
  • Restoration of old fiberglass domes, flat roofs, polycarbonate, other composite materials, etc.
  • Concrete and polymer floors.
  • Waterproofing and protection of metal structures, printed floor coverings, micro cements, leveling maltine, mosaics, mineral gravel.
  • Flexible quartz slip products, corundum, rubber, dust, etc.

ADVANTAGES

  • A single component product, extremely easy to use.
  • No errors and lost time.
  • Total color stability under the sun and UV rays.
  • Excellent resistance to abrasion and wear.
  • Rapid hardening and protection of possible paints.
  • Good coverage capacity.

AVAILABLE COLORS

  • Transparent (the matt version is available using Matting Additive – see data sheet).
  • RAL, always pigmented and only immediately before application.

RESITEX

RESITEX is a TNT thermally bonded geotextile fabric, based on polyester / polyamide synthetic fibers, with high modulus of elasticity and tensile strength.

RESITEX 80

It has been developed to be applied in situ by the interposition of fresh over and between the different layers of RESIMPER resin, in order to obtain a thickness as homogeneous as possible and consequently an optimal distribution of the product in Limiting the effect of leaks.

RESITEX 200

It is recommended for final abrasion protection and a homogeneous distribution of the empty weight of the resins coated support RESIMPER membranes of highly elastic polyurethane. Ideal in situations that require additional armor protection, or protection and optimum thickness distribution, with minimal loss of mechanical properties.
Product compatible with solvents and strong absorption.
Flexible and adaptable to uneven surfaces, edges and angles, critical points of lifting and overlaps of old bituminous membranes, Ideal for assembling junction points between interdependent media or different type or material, cracks and macro- Cracks, joints and cuts, etc.
High elasticity, in order to maintain as much as possible the mechanical properties of the membranes, which increases its resistance to perforation and perforation due to plant roots.
Inside and outside edges, front reinforcement, backbones and other singular points or as a « weed control » system prior to installation of the RESIMARMO system.

RESITEX 200 membrane protection RESIMPER for: concrete tiles, wood, wood panels, composite materials, cement boards, floating floors, etc.

Technical certifications obtained

  • ETA : European Technical Assessment document Nº 06/0263 – CE marking : 10 and 25 years.
  • Flat roof external fire exposure Nº 06/32301345
  • Roof 45º fire resistance Nº 08/32309237
  • Root perforation no RESIMPER Nº 07/32305556 with RESIMPER Nº 07/32305557
  • Abrasion Taber Nº 10/101.729-1626
  • QUALICONSULT : Notebook of Technical Terms CCT nº 50 712 004 096 MS
  • BBA : British Board of Agreement 11/4836
  • IETcc report 19.221-II (2007) on thermal resistance.

 

The resins - RESIMARMO Technical Certifications

 

 

CONTACT FORM

Visitor contact form
  • For maximum security on our sites, you are invited to solve this puzzle. Write your answer below the CAPTCHA field.

 

 

 

 

 

Logo of color